Neuspeed 65.10.61 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Neuspeed 65.10.61. Neuspeed 65.10.61 User Manual [en] [cs] [de] Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 3
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
NEUSPEED 3300 Corte Malpaso • Camarillo, CA 93012 • 805.388.7171 • 805.388.0030 FAX
www.neuspeed.com
P-FLO COLD AIR INTAKE FOR 1993-99.5 GOLF III / JETTA III VR6
PART # 65.10.61
INSTALLATION INSTRUCTIONS
PARTS LIST: 1 HEAT SHIELD 1 PUSH FASTENER
1 P-FLO BRACKET 1 SHEET METAL SCREW
1 AIR FILTER 1 HEX KEY WRENCH
1 MINI FILTER 2
6
/
32
” X
5
/
8
” BUTTON CAP SCREWS
1 HOOD SEAL 2 #6 WASHERS
2 8mm NYLOC NUTS 2 OVAL SHAPED NUTS
TOOLS REQUIRED: 1 FLAT SCREW DRIVER 1
3
/
8
WRENCH or SOCKET
1 PHILIPS SCREW DRIVER 1 10mm WRENCH
1 DRILL MOTOR 1 13mm WRENCH
1 ¼” DIAMETER DRILL
1. First, disconnect electrical connector, and intake tube
from mass air sensor. Next remove the one rubber ‘O’
ring that holds the air box to the frame. Completely
remove hose at front corner of air box lid on down to
plastic tube near front corner of alternator. Now
remove air box.
2. Install mini-filter to air pump.
3. Unclip two clips to separate mass air sensor from air
box.
4. Mount metal NEUSPEED P-Flo bracket to existing
studs on side of strut tower.
5. Mount mass air sensor to BACK SIDE of bracket
with hardware and hex key wrench supplied (align slots
with hole in bracket). Install screw and flat washer
from FRONT SIDE of bracket through mass air sensor
slots. Use the oval shaped threaded nuts on BACK
SIDE, with large area (flat side) against bracket.
Tighten both screws.
6. Re-install intake hose to mass air sensor and re-
connect electrical connector. At this point, your
installation should like what is pictured above.
7. Insert lower front portion of the shield under the
radiator support and slide bottom edge of shield into
slot between AC condenser line and chassis seam.
Rotate rear portion of shield down and into position,
making sure any hoses and/or electrical lines are routed
through cut outs.
Vue de la page 0
1 2 3

Résumé du contenu

Page 1

NEUSPEED • 3300 Corte Malpaso • Camarillo, CA 93012 • 805.388.7171 • 805.388.0030 FAX www.neuspeed.com P-FLO COLD AIR INTAKE FOR 1993-99.5 GOLF III

Page 2

NEUSPEED • 3300 Corte Malpaso • Camarillo, CA 93012 • 805.388.7171 • 805.388.0030 FAX www.neuspeed.com 8. Due to slight variations in vehicle

Page 3 - DOC.65.10.61 Rev. 06.19.02

NEUSPEED • 3300 Corte Malpaso • Camarillo, CA 93012 • 805.388.7171 • 805.388.0030 FAX www.neuspeed.com 11. Pass newly supplied filter through opening

Commentaires sur ces manuels

Pas de commentaire